Independent Repair

Can not find the solution to the problem of your appliance or electric? Do not panic, Notices-Online has set up a stand-alone diagnostic platform, which will allow you to find a solution in record time.
How it works ?
The standalone diagnostic tool is extremely easy to use, you will only have to follow a series of questions crafted by our experts, which should lead you directly to the problem faced by your device. This tool is totally free and very useful so do not hesitate!
Encountered problem :
Scheduler problem
The display flashes or displays horizontal lines
The supply wires are loose, tighten them in the junction box. The power supply wires are tight, it is a problem of electrical network, contact EDF or an electrician
The display resets, time change or consistency problem in the clock
This is a problem related to the electronic module of the device, we advise you to call a convenience store to replace the power of your oven.
Electronic programmer
This is a problem related to the electronic module of the device, we advise you to call a convenience store to replace the power of your oven.
Mechanical programmer
Test the timer of your oven. It contains 4 lugs, using a measuring device, check the continuity between the brown wire of the arrival lug which is at the top and the brown wire of the terminal lug which is at the bottom. Do the same thing with the blue wires. If the test is inconclusive, please contact a specialist directly.
My oven is heating up too much
Test the mechanical thermostat, if it is defective, replace it. If the mechanical thermostat is working, it is probably a problem with the probe of your oven. You can test it with an ohmmeter type device.
My oven does not heat up enough
Test the resistance of the rotating heat using this same function. If there is no increase in temperature or it is not sufficient, please check the correct operation of the rotating fan. If there is an increase in temperature, please test the other available programs in your oven to find the faulty one and contact a professional. If the test is inconclusive, please contact a specialist directly.
The oven makes noise
The rotating heat helix is ​​loosened
Check the tightness of the propeller at the bottom of the oven.
The cooling fan is damaged
The cooling fan is usually located on the top of your oven. Try to put grease on the cooling fan shafts. If the noise persists, change the fan.
The mechanical pendulum is broken
If it is the mechanical pendulum that is in question, you will have to change it.
The sheets are poorly screwed
Check the screws and the correct fastening of the sheets.
Door security and the electronic card are faulty
The security or the electronic card may be faulty. If so, it must be changed.
The oven does not heat
The power supply is faulty
Check that your oven is supplied with electricity. Also check the electrical installation.
The door lock is broken
If the door lock is broken, the oven will not know if the door is closed or not. If it is defective, change it.
Adjustable thermostat is defective
Check the thermostat using a multimeter in the Ohmmeter position. If there is no continuity, the adjustable thermostat must be replaced.
The temperature sensor is faulty
It may be from the temperature sensor. If so, change it.
The electrical terminal block is loose
Check the electrical terminal block on the back of your oven. If it is defective, replace it.
The safety thermostat is faulty
Check the thermostat status using a multimeter in the Ohmmeter position. Check for continuity by placing the two tester tips on each terminal of the thermostat. If the value is zero, you must change the safety thermostat.
Grill resistance does not work anymore
Heat your oven and place your hand over the oven. If you do not feel hot, it will change the grill resistance.
The sole resistance is defective
As for grill resistance, place your hand at the bottom of the oven. If no heat is emitted, change the sole resistance.
Circular resistance is damaged
Check the resistance continuity using a multimeter in Ohmmeter position. If the continuity is not busy, you have to change the circular resistance.
The oven lamp does not light anymore
The lamp is defective
Check the condition of the lamp. Replace it with a specific bulb.
The lampholder has a false contact
There may be a false contact. Test the lamp socket. If it does not work, change it.
The safety thermostat is faulty
Check the thermostat status using a multimeter in the Ohmmeter position. Check for continuity by placing the two tester tips on each terminal of the thermostat. If the value is zero, you must change the safety thermostat.
The electrical terminal block is loose
Check the electrical terminal block on the back of your oven. If it is defective, replace it.
The electrical wires are damaged
Check the condition of the electrical wires.
The electronic card is faulty
The electronic card allows you to manage all the functions of your oven. If all the problems mentioned above have been verified, the electronic card must be replaced.
The oven does not turn on
The power supply is faulty
Check that your oven is supplied with electricity.
The lamp is out of order
The lamp does not work and must be replaced.
Demo mode is on
Disable this mode using the manufacturer's manual.
Child safety is engaged
Disable child lock using the manufacturer's manual.
The electrical terminal block is damaged
Check the electrical terminal block on the back of your oven. If it is defective, replace it.
The safety thermostat is faulty
Check the thermostat status using a multimeter in the Ohmmeter position. Check for continuity by placing the two tester tips on each terminal of the thermostat. If the value is zero, you must change the safety thermostat.
The electronic card is faulty
The electronic card allows you to manage all the functions of your oven. If all the problems mentioned above have been verified, the electronic card must be replaced.
The dishwasher overflows and leaks through the door
Wash arms are damaged
Check the condition of the wash arms and change them if necessary.
There is too much rinse aid
Too much rinse aid is present.
The baskets are poorly positioned
Check the correct location of the rail baskets.
Door seals are defective
Check the condition of the door seals and change them if necessary.
The drain pump is faulty
Check the condition of the drain pump and change it if necessary.
The pressure switch is damaged
Check the condition of the pressure switch and change it if necessary.
The compression chamber is obstructed
Check that the compression chamber is not obstructed.
Dishwasher makes break
The power supply is faulty
Check the conformity of your electrical installation.
Resistance is defective
Check the condition of the resistor and change if necessary.
Door security is damaged
Check the door security status and change it if necessary.
Check for a water leak
Check for water leaks.
The electric wires are worn
Check the condition of your electrical wires and change them if necessary.
The dishwasher makes noise
The power supply is faulty
Check the conformity of your electrical installation.
Resistance is defective
Check the condition of the resistor and change if necessary.
Door security is damaged
Check the door security status and change it if necessary.
Check for a water leak
Check for water leaks.
The electrical wires are damaged
Check the condition of your electrical wires and change them if necessary.
The dishwasher is leaking
Plumbing installation is not in compliance
Your plumbing installation is not compliant.
Wash arms are blocked
Check the condition of the wash arms and change them if necessary.
There is too much rinse aid
Too much rinse aid is present.
The seals are worn
Check the condition of the seals and change them if necessary.
The pressure switch is faulty
Check the condition of the pressure switch and change it if necessary.
The compression chamber is obstructed
Check that the compression chamber is not obstructed.
The tank is pierced
Check the condition of the tank and replace if necessary.
The dishwasher does not heat up
Plumbing installation is not adequate
Plumbing installation does not comply.
The drain filter is clogged
Check that the drain filter is not clogged.
Resistance is out of order
Check the condition of the resistor and replace if necessary.
The temperature sensor is defective
Check the condition of the temperature sensor and replace if necessary.
The compression chamber is clogged
Check that the compression chamber is not obstructed.
The pressure switch is faulty
Check the condition of the pressure switch and replace if necessary.
The high pressure switch is faulty
Check the condition of the pressure switch and change it if necessary.
The thermostat is defective
Check the condition of the thermostat and replace if necessary.
The electrical wires are damaged
Check the condition of your electrical wires and change them if necessary.
The dishwasher does not drain anymore
Plumbing installation is not in compliance
Plumbing installation is not compliant.
The drain filter is clogged
Check that the drain filter is not clogged.
The drain pump is blocked
Disassemble and clean the pump. Change if necessary.
The solenoid valve is damaged
Check the condition of the solenoid valve and change it if necessary.
The electrical wires are damaged
Check the condition of your electrical wires and change them if necessary.
The dishwasher is not washing properly
The program is not suitable
The wash program is poorly chosen.
Filters are clogged
Check that the filters are not clogged.
The arms are clogged
Check that the arms are not clogged.
Laundry is not good
Change laundry.
No salt in the dishwasher
Put salt in the tank.
The washing pump is clogged
Unclog the wash pump.
Technical problem when lighting
the problem is manifested by an uninterrupted flashing of the central indicator. The magnet in question is blocked, it is not moving.
Limestone may block the movement of the magnet at the bottom of the tank. To solve this problem, pour white vinegar into the tank and wait at least 15 minutes.
The problem is manifested by an uninterrupted flashing of the central indicator. The magnet is not blocked, it is moving.
In this case, the magnet is not the cause of your problem. You can check the water presence sensor. If you notice any malfunction, change it.
The LED flashes quickly and then turns off quickly.
If so, you must change the condenser of your coffee maker. To do this, you will need to dismantle your coffee maker to reach the order.
My coffee maker has a temperature problem
The water poured into my coffee maker no longer heats
Check the temperature sensor. If it is defective, change it.
The water flow of my coffee maker is not done normally
The pump is working but I can not open the pod valve. The damper flap is blocked
If your butterfly valve is blocked, you must wait for the pressure to go down before you can unblock it. Once the pressure has gone down, open the pod valve and clean it. Do not reuse the same used pod.
The water in my coffee maker is not flowing well with a very low intensity. A descaling is necessary
Solution: fill the water tank of your coffee maker with water up to half.This will be more effective if you use lukewarm water.Fill the second half of the tank with white vinegar.Put a pod used in the pod holder then close the lid Place a bowl underneath to collect the liquid Then press the 2 cups button and let the machine run Repeat the operation until the tank is empty. Once done, refill the freshwater tap water tank and run the machine by pressing the 2 cups button until the tank is empty again.
The pump is defective
First of all, check that your coffee machine is well supplied with electricity. If yes, and nothing is happening, dismantle the coffeemaker to make sure the lugs are properly connected. If your problem persists, the pump is defective and needs to be replaced.
The water reserve is clogged
If this is the case, disassemble the tank and clean it with white vinegar to unlock the valve. If that does not work, change the damper or the full tank.
The water filter is clogged
The purpose of the water filter is to filter out impurities in the water. If it is clogged, disassemble it if possible to clean it.
The flowmeter is scaled
If your pump is scaled, the water pressure will not be sufficient. To do this, do a descaling of your coffee maker. If the problem is still not resolved, change it.
The safety valve is obstructed
The safety valve serves as protection for the circuit. If this is obstructed, do a complete descaling. If nothing happens, change the valve.
Solenoid valve is blocked
If your solenoid valve is blocked, try descaling. If the problem persists, change it.
My coffee maker is leaking
The water tray is cracked
Check the condition of the water tank. If it is damaged or punctured, change it.
The seals are worn
To begin, pour water into the tank and see if any water flows down the joint below. If this is the case, the seal is worn out and you need to replace it.
The hoses broke out
If the hoses are damaged, change them. To avoid this kind of problem in the future, consider descaling regularly.
Resistance is cracked
The resistance can crack with time or because of the limestone. Change the resistance if it is cracked. To avoid this kind of problem in the future, consider descaling regularly.
The percolator is no longer waterproof
The percolator can wear out over time and start to leak. Check the seal. If it is damaged, replace it.
Steam nozzle is scaled
The steam nozzle may leak over time. Try to do a complete descaling. If the problem persists, change it.
The position valve is loose
Check that the position valve is not loose. If it's not the case, you'll have to change it.
My coffee maker makes cold and clear coffee
The percolator group is scaled
Try to do a complete descaling. If the problem persists, change the part.
Control thermostat is faulty
If your control thermostat fails, you will have to change it.
The temperature sensor is defective
If your temperature sensor fails, you will unfortunately have to change it.
The safety thermostat is activated
Start by checking the level of scaling of the tubes that connect the resistor. If necessary, do a descaling. If your thermostat fails, you will unfortunately have to change it.
The resistance is faulty
The heater heats the water before dispensing it. If the resistance is defective, you will unfortunately have to change it.
The electronic board is faulty
The purpose of the electronic card is to manage all the functions of the coffeemaker. If all the problems mentioned have been checked and the water still does not heat up, it will be necessary to replace the electronic card.
My coffee maker does not work anymore
The power supply is faulty
First, check that the coffee maker is well supplied with electricity. Then check that your power outlet is working properly. Also check the condition of the cable. If it is damaged, change it.
The power switch is damaged
Start by testing your switch with a multimeter in the Ohmmeter position. If no value appears, it probably needs to be changed.
The safety thermostat is triggered
The thermostat is used to limit the temperature. If it malfunctions, the water will not be properly heated. If this safety thermostat is defective, change it.
Security does not work
It only takes one security for the coffee maker to refuse to start. To do this, check that there are no leaks.
The machine is scaled
Make a descaling. To avoid this kind of problem in the future, consider descaling regularly.
The electronic card is faulty
The purpose of the electronic card is to manage all the functions of the coffeemaker. If all the problems mentioned have been checked and the water still does not heat up, it will be necessary to replace the electronic card.
The washing machine does not spin
The power supply is faulty
Check that your device is properly powered. Also check the correct operation of the power socket.
An unbalance is caused by the laundry
Your machine may have stopped because of a bad positioning of your laundry. Be careful to respect the weight of linen.
Pump or drain filter is clogged
Check that the pump or filter is not clogged. If so, clean them. If it is damaged, you will have to change it.
The drain hose is clogged
Check that the hose is not clogged. Disassemble the hose and clean it. If it is damaged, change it.
There is too much foam when spinning
There may be too much laundry in the machine.
The belt is out of its axis or broken
Try to replace the strap. If it does not fit, replace it.
The pressure switch does not work properly
Start by checking and cleaning the compression chamber. If it still does not work, change it.
The motor coals are worn
Coals can wear out with time. If your coals are less than 1 cm, you will have to change them.
Door security does not work properly
Test door security. If it fails, change it.
The solenoid valve remains open permanently
Clean the solenoid valve and change if necessary.
The electronic card is faulty
The electronic card manages all the functions of the washing machine. If all the problems mentioned have been verified, change the electronic card.
The washing machine fills with water too slowly
The water tap is not open enough
Check the flow of your water faucet. Open more if necessary.
The water is evacuated by self-siphoning
Check that the drain tube is not more than 10 cm inside the pipe. The pipe must be more than 65 cm from the ground.
Solenoid valve does not work properly
Check the condition of the solenoid valve and change it if necessary.
The compression chamber is clogged
Check the compression chamber and clean it if necessary.
The pressure switch is defective
Check the condition of the pressure switch with a multimeter and replace if necessary.
The electronic board does not work normally
The electronic card manages all the functions of the washing machine. If all the problems mentioned have been verified, change the electronic card.
The washing machine smells bad
The machine stays open too often
Remember to ventilate your machine after use.
The washing temperature is too low
Increase the temperature of your program.
There is not enough laundry
Put more laundry.
There is a sewage disposal problem
Check the evacuation of your wastewater.
The laundry stays too long in the machine
Remember to take out the laundry after the end of the machine.
The washing machine is staining the clothes
There is too much laundry in the machine
Respect the recommended weight of linen.
There is too much softener
You put too much softener.
The belt is damaged
Try to replace the strap. If it does not fit, replace it.
Bearings or bearings are worn
Check the condition of the bearings or bearings and change if necessary.
Resistance is fouled
Disassemble and clean the resistor. Replace if necessary.
There is mold in the door seal
Your door seals may be moldy. Clean or replace them.
The plumbing installation is in question
Plumbing installation is not compliant.
The window of the washing machine does not open anymore
There is a power supply problem
Check that your device is properly powered. Also check the correct operation of the power socket.
The door handle is blocked
The door handle can be blocked. Try to unlock it.
Door security is damaged
Check the status of the security and the connector. Replace if necessary.
Filter or drain pump is clogged
Check that the pump or filter is not clogged. If so, clean them. If it is damaged, you will have to change it.
The temperature sensor is defective
Check the condition of the temperature sensor and change it if necessary.
The pressure switch is defective
Check the condition of the pressure switch with a multimeter and replace if necessary.
The electronic card is faulty
The electronic card manages all the functions of the washing machine. If all the problems mentioned have been verified, change the electronic card.
The washing machine will not start
The washing machine is not supplied with electricity
Check that your device is properly powered. Also check the correct operation of the power socket.
The washing program is poorly selected
The wash program may not have been selected.
The door does not close anymore
Check the closing of the door.
There is a water supply fault
Check the water supply.
Door security is faulty
Check the condition of the door security and change it if necessary.
Solenoid valve is damaged
Check the condition of the solenoid valve and change it if necessary.
Resistance is defective
Check the condition of the resistor and change it if necessary.
The engine no longer works
Check the condition of the engine and change it if necessary.
The electronic card is faulty
The electronic card manages all the functions of the washing machine. If all the problems mentioned have been verified, change the electronic card.
The washing machine does not drain
The drain filter is obstructed by an object
Check that the drain filter is not clogged by an object.
Drain hose is bent or clogged
Check that the drain hose is not clogged.
The drain hose is clogged
Check that the drain hose is not clogged.
Solenoid valve does not close properly
Check the condition of the solenoid valve and change it if necessary.
There is too much foam when draining
There may be too much laundry in the machine.
The belt is broken
Try to replace it or replace it if necessary.
The washing machine makes break
The drain pump is defective
Check the condition of the drain pump and change it if necessary.
Your washing machine has a water leak
Check that there is no water leak.
The wiring is damaged
Check the condition of the cables and change if necessary.
Door security is blocked
Check the condition of the door and change if necessary.
The washing machine is leaking
There is a bad installation of the device
The installation is not compliant.
Do not put too much laundry
There is too much laundry in the machine.
The door seal is damaged
Check the condition of the door seal and change it if necessary.
The drain pump is clogged
Check that the drain pump is not clogged by an object.
The compression chamber is clogged
Check the condition of the compression chamber and clean it.
The pressure switch is damaged
Check that it is working properly and replace it if necessary.
The tank is pierced or broken
Check the condition of the tank and change if necessary.
The electronic card is faulty
The electronic card manages all the functions of the washing machine. If all the problems mentioned have been verified, change the electronic card.
The washing machine does not wash anymore
You put too much linen
There is too much laundry in the machine. Respect the recommended weight.
Bad choice of laundry
Laundry is not effective.
The drain pump is clogged
Check that the drain pump is not clogged.
Resistance is damaged
Check the condition of the resistor and change if necessary.
The temperature sensor is defective
Check the condition of the temperature sensor and change it if necessary.
The pressure switch is damaged
Check the condition of the pressure switch and change it if necessary.
The belt is broken or off-center
Try to replace it or replace it if necessary.
The electronic card is faulty
The electronic card manages all the functions of the washing machine. If all the problems mentioned have been verified, change the electronic card.
The washing machine stops during the cycle
The device is no longer electrically powered
Check that your device is properly powered. Also check the correct operation of the power socket.
There is a problem with the water supply
Water does not arrive properly.
Your plumbing system is not compliant
Change your plumbing
The drain filter is clogged by an object
Check that the drain filter is not clogged.
Solenoid valve does not work properly
Check the condition of the solenoid valve and change it if necessary.
Resistance is defective
Check the condition of the resistor and change if necessary.
Resistance is defective
Check the condition of the resistor and change it if necessary.
The temperature sensor is faulty
Check the condition of the temperature sensor and change it if necessary.
The electronic card is faulty
The electronic card manages all the functions of the washing machine. If all the problems mentioned have been verified, change the electronic card.
My vacuum does not aspire anymore
The power wheel is out of adjustment
Remember to check if your power dimmer button is not in the low position. Increase the power of the dimmer button. If you hear that the vacuum cleaner is running faster, it's a good sign. Otherwise, it will need to be replaced.
The vacuum bag is full
Check the bag or tank to make sure it is not full. Empty it if necessary.
The dust filter is clogged
The filter prevents some dust from passing and can very quickly become dirty. Disassemble the filter and shake / clean it to remove large dust.
The pipe is clogged or clogged
Dismantle the hose at both ends to make sure you have not sucked up an object that clutters the passage. For this, use a metal hanger or wire to pass through the pipe and extract the bulky objects.
The brush is dirty
The brush can sometimes hang with the most often hair or animal hair. Disassemble your brush and clean it.
The engine is blocked
The motor allows the vacuum cleaner to operate. If it is obstructed, the vacuum cleaner may have difficulty in fulfilling its primary mission to know how to suck. Do not inhale flour or plaster as this can damage your motor.
The motor capacitor is defective
To check the correct operation of the motor capacitor, have a multimeter in the Ohmmeter position. Disconnect the cables from the connectors and place the tips of the tester on them. If the capacitor works, the value goes up or down gradually. In the opposite case, there is a high probability that the capacitor is defective.
There is an air leak in the circuit
Check that there are no holes in the suction system or parts of the vacuum cleaner that are not properly connected. Check that the vacuum hose is properly connected and that the seals are in place and not damaged. Replace the seals if they are damaged.
The rotating brush of the vacuum cleaner does not work
Rotating brush is broken
Check that the small belt connecting the two wheels of the brush is not broken. If so, you must change the rotating brush.
The engine is blocked
The motor of the brush can be blocked by hair for example. If this is the case, disassemble your brush and clean it.
The battery no longer holds the charge
Check that the charging transformer is working properly. If the battery still does not hold the battery, you must replace it.
My vacuum makes a lot of noise
Rotating brush is dirty
Disassemble your rotary brush and clean it. Remember to do it regularly.
Tube or hose are clogged
An object or large dust may be stuck in the tube. If this is the case, remove the hose at both ends to check that you have not sucked up an object that clogs the passage. For this, use a metal hanger or wire to pass through the pipe and extract the bulky objects.
The bag is full
Check the bag or tank to make sure it is not full. Empty if necessary.
Filters are clogged
The filter prevents some dust from passing and can very quickly become dirty. If you hear a noise that the vacuum does not suck, remove the filter and shake / clean it to remove large dust.
The engine is blocked
The motor allows the vacuum cleaner to operate. If it is obstructed, the vacuum cleaner may have difficulty in fulfilling its primary mission to know how to suck. Do not inhale flour or plaster as this can damage your motor.
The vacuum cleaner does not work anymore
There is a problem with the power supply
Check that the power outlet is working. To be sure, plug another device into this jack. Also check your breaker to verify that a lead has not jumped. If nothing happens, it's because the plug is not working.
The power cord is damaged or severed
Check the condition of the electrical wire. If it is in poor condition, do not take risks and change it. If the vacuum cleaner starts when you handle the wire, there is a false contact. Do not take chances and change the power cord.
The reel is damaged
If your retractor is damaged or malfunctioning, do not take any risks and change it.
The switch is damaged
The switch can make a false contact. If so, change it.
The engine is blocked
Check that the motor is not blocked by dirt. To do this, dismount it. On most vacuums, it is behind the filter.
My vacuum cleaner heats up and smells like burnt
The vacuum cleaner is dirty
The vacuum cleaner may be dirty so if you can, clean it with products that smell good.
Tube or hose are clogged
An object or large dust may be stuck in the tube. If this is the case, remove the hose at both ends to check that you have not sucked up an object that clogs the passage. For this, use a metal hanger or wire to pass through the pipe and extract the bulky objects.
The vacuum bag is full
Check the bag or tank to make sure it is not full. Empty if necessary.
The dust filter is clogged
The filter prevents some dust from passing and can very quickly become dirty. Disassemble the filter and shake / clean it to remove large dust.
The refrigerator light does not work
The lamp does not work
Change the lamp.
The power supply is faulty
The power supply is faulty.
The switch is damaged
Check its condition and change it if necessary.
The lamp socket is off
Check its condition and change it if necessary.
The electronic card is faulty
The electronic card can manage all the functions of the refrigerator. If all the problems mentioned have been verified, change the electronic card.
My fridge makes break
The power cord is defective
Replace the power cord of the fridge or have it done by a professional.
The power cord is in good condition
I test the defrosting resistance, for that you will need a measuring device measuring the value in Kilo Ohms between the terminals. If it is defective, please replace it. If it is in good condition, please check the refrigerator motor components.
The refrigerator is struggling to get cold
The thermostat is incorrectly set
Set the thermostat.
There is a layer of frost on the walls
Remove the layer of frost.
The capacitor is damaged
Check its condition and change it if necessary.
The fan is defective
Check its condition and change it if necessary.
The refrigerator is not properly closed
Check and close.
The refrigerator does not work anymore
The power supply is faulty
Check the power supply.
The lamp is defective
Change it and try again.
Fan motor is faulty
Check its condition and change it if necessary.
Control thermostat is out of order
Check its condition and change it if necessary.
The electronic card is faulty
The electronic card can manage all the functions of the refrigerator. If all the problems mentioned have been verified, change the electronic card.
The refrigerator smells bad
The refrigerator is dirty
Clean it.
The temperature is not suitable
Set the temperature.
The defrosting pan is dirty
Clean it.
The compressor is defective
Check its condition and change it if necessary.
Ventilation is faulty
Check its condition and change it if necessary.
My hood no longer works
The power supply is faulty
Check the power supply of your hood.
The connector is not properly fitted
Check that the connector is nested.
The function selector is defective
Check the status of the function selector. Change if necessary.
The motor capacitor is damaged
Check the condition of the motor capacitor. Change if necessary.
The turbine is loose
Check the condition of the turbine tightening. Replace if it is broken.
The suction motor is blocked
Check that the suction motor is not dirty. Also check the filters.
Filters are clogged
Disassemble and clean the filters.
The electronic board is faulty
The electronic card can manage all the functions of your hood. If all the problems mentioned above have been verified, the electronic card must be replaced.
The hood is noisy
The choice of hood is decisive
Remember to check the sound level of the hood before the purchase.
The check valve is loosened
Check the condition of the check valve tightening. This problem may be due to fat.
The carbon filters are worn
Active carbon filters are normally replaced every 3 months. If the filters are defective, change them.
The turbine is loose
Check the correct fastening of the turbine. If it looks bad, change it.
The engine mount is cracked
Check the condition of the motor mount. Change it if necessary.
The suction motor is oxidized
If the engine is oxidized, it will not work properly. In this case, change it.
The hood is noisy
The motor turns freely
I test the engine by throwing the turbine by hand, I check the condition of the capacitor. If it is defective, the engine will not spin.
The hood has a water leak
The installation does not comply
Check that the entire installation of your hood is compliant. If you notice an abnormality, contact a technician.
Location is not good
Check the correct location of your hood especially in relation to condensation.
The evacuation exit is not well equipped
Check the presence of a check valve for the exhaust outlet. Without it, the cold air from outside can come in and make condensation. If there are none, install one.
The hood no longer aspires
The installation does not comply
Check that the entire installation of your hood is compliant. If you notice an abnormality, contact a technician.
The evacuation tube is damaged
Check the condition of the exhaust tube. Change it if it is damaged.
The check valve is blocked
Check that the check valve is not blocked by grease. Clean it.
Filters are clogged
Disassemble and clean the carbon filters with product.
The turbine is loose
Check the correct fastening of the turbine. If it looks bad, change it.
The suction motor is oxidized
If the engine is oxidized, it will not work properly. In this case, change it.
The electronic board is faulty
The electronic card can manage all the functions of your hood. If all the problems mentioned above have been verified, the electronic card must be replaced.
The hood lamp does not light anymore
The power supply is faulty
Check the power supply of your hood.
The lamp does not work anymore
The lamp may be involved. If it does not work anymore, change it.
The lamp socket has a false contact
There may be a false contact with the lamp socket. If so, change the lamp socket.
The transformer is faulty
Check the transformer using a multimeter in the voltmeter position. If no value appears, you must change it.
The light switch is defective
He may have a false contact or be defective. If so, change it.
Microwave light does not work
The lamp does not work
Change the microwave lamp.
There is a false contact with the lampholder
There is a false contact with the lampholder. Change the socket.
Door security is damaged
Check its condition and change it if necessary.
Problem with the electronic card
The electronic card allows you to manage all the functions of the microwave. If all the problems mentioned have been verified, change the electronic card.
The lamp does not work
Change the lamp
The microwave is noisy
Turntable is damaged
Check its condition and change it if necessary.
The fan is damaged
Check its condition and change it if necessary.
The capacitor is defective
Check its condition and change it if necessary.
The magnetron is faulty
Check its condition and change it if necessary.
Microwave makes break
The electrical installation is faulty
Check the electrical installation and try again.
The suppressor capacitor is inflated
Check its condition and change it if necessary.
Door security is damaged
Check its condition and change it if necessary.
The capacitor is defective
Check its condition and change it if necessary.
The transformer is faulty
Check its condition and change it if necessary.
The microwave does not work
The electrical installation is faulty
Check the electrical installation and try again.
The suppressor capacitor is inflated
Check its condition and change it if necessary.
Door security is damaged
Check its condition and change it if necessary.
The capacitor is defective
Check its condition and change it if necessary.
The transformer is faulty
Check its condition and change it if necessary.
My turntable does not work
The engine runs
So this is a training problem, check the plate, the turntable support and the turntable driver.
The engine does not run
In most cases, the engine is defective, so it must be changed.

Dear participant,

It seems that You have already been registered in the competition, you can do that just once. Be patient, as soon as you win the prize, you will be contacted by email. For any further questions please contact our support department